Toshiba Credit Card Machine ST 71 User Manual

TOSHIBA POS Terminal  
ST-71 SERIES  
Owner's Manual  
 
Safety Summary  
EO1-12031  
Safety Summary  
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions  
necessary for safe handling are included in this manual. All warnings and cautions contained in this manual  
should be read and understood before handling or maintaining the equipment.  
Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified  
using the procedures described in this manual, turn off the power, unplug the machine, then contact your  
authorized TOSHIBA TEC representative for assistance.  
Meanings of Each Symbol  
This symbol indicates warning items (including cautions).  
Specific warning contents are drawn inside the symbol.  
(The symbol on the left indicates a general caution.)  
This symbol indicates prohibited actions (prohibited items).  
Specific prohibited contents are drawn inside or near the symbol.  
(The symbol on the left indicates “no disassembling”.)  
This symbol indicates actions which must be performed.  
Specific instructions are drawn inside or near the symbol.  
(The symbol on the left indicates “disconnect the power cord plug from the outlet”.)  
This indicates that there is the risk of death or serious injury if the  
machines are improperly handled contrary to this indication.  
WARNING  
Do not plug in or unplug the  
power cord plug with wet  
hands as this may cause  
electric shock.  
Do not use voltages other than the  
voltage (AC) specified on the  
rating plate, as this may cause fire  
or electric shock.  
Any other than the  
specified AC voltage is  
prohibited.  
Prohibited  
Prohibited  
If the machines share the same  
outlet with any other electrical  
appliances that consume large  
amounts of power, the voltage  
will fluctuate widely each time  
these appliances operate. Be  
sure to provide an exclusive  
outlet for the machine as this  
may cause fire or electric  
shock.  
Do not place metal objects or  
water-filled containers such as  
flower vases, flower pots or mugs,  
etc. on top of the machines. If  
metal objects or spilled liquid enter  
the machines, this may cause fire  
or electric shock.  
Prohibited  
Do not insert or drop metal,  
flammable or other foreign  
objects into the machines  
through the ventilation slits, as  
this may cause fire or electric  
shock.  
Do not scratch, damage or modify  
the power cords. Also, do not  
place heavy objects on, pull on, or  
excessively bend the cords, as this  
may cause fire or electric shock.  
Prohibited  
Prohibited  
If the machines are dropped or  
their cabinets damaged, first  
turn off the power switches and  
disconnect the power cord  
plugs from the outlet, and then  
contact your authorized  
TOSHIBA TEC representative  
for assistance. Continued use  
of the machine in that condition  
may cause fire or electric  
shock.  
Continued use of the machines in  
an abnormal condition such as  
when the machines are producing  
smoke or strange smells may cause  
fire or electric shock. In these  
cases, immediately turn off the  
power switches and disconnect the  
power cord plugs from the outlet.  
Then, contact your authorized  
TOSHIBA TEC representative for  
assistance.  
Disconnect  
the plug.  
Disconnect  
the plug.  
(i)  
 
Safety Summary  
EO1-12031  
If foreign objects (metal  
When unplugging the power cords,  
be sure to hold and pull on the plug  
portion. Pulling on the cord portion  
may cut or expose the internal wires  
and cause fire or electric shock.  
Disconnect  
the plug.  
Disconnect  
fragments, water, liquids) enter  
the machines, first turn off the  
power switches and disconnect  
the power cord plugs from the  
outlet, and then contact your  
authorized TOSHIBA TEC  
representative for assistance.  
Continued use of the machine in  
that condition may cause fire or  
electric shock.  
the plug.  
Ensure that the equipment is  
properly grounded. Extension  
cables should also be grounded.  
Fire or electric shock could  
occur on improperly grounded  
equipment.  
Do not remove covers, repair or  
modify the machine by yourself.  
You may be injured by high  
voltage, very hot parts or sharp  
edges inside the machine.  
Unauthorized modification is  
prohibited.  
Connect a  
No  
disassembling.  
grounding wire.  
This indicates that there is the risk of personal Injury or damage to objects if  
the machines are improperly handled contrary to this indication.  
CAUTION  
Precautions  
The following precautions will help to ensure that this machine will continue to function correctly.  
Try to avoid locations that have the following adverse conditions:  
* Temperatures out of the specification  
* Shared power source  
Do not subject the machine to sudden shocks.  
* Direct sunlight  
* High humidity  
* Dust/Gas  
* Excessive vibration  
Do not press the keys too hard. Keys will operate correctly if they are touched lightly.  
Clean the cover and keyboard, etc. by wiping with a dry cloth or a cloth soaked with detergent and  
wrung out thoroughly. Never use thinner or other volatile solvent for cleaning.  
At the end of the day, turn the power OFF, then clean and inspect the exterior of the machine.  
Try to avoid using this equipment on the same power supply as high voltage equipment or equipment  
likely to cause mains interference.  
USE ONLY TOSHIBA TEC SPECIFIED consumables.  
DO NOT STORE the consumables where they might be exposed to direct sunlight, high temperatures, high  
humidity, dust, or gas.  
When moving the machine, take hold of the drawer and lift the machine.  
Do not place heavy objects on top of the machines, as these items may become unbalanced and fall  
causing injury.  
Do not block the ventilation slits of the machines, as this will cause heat to build up inside the  
machines and may cause fire.  
Do not lean against the machine. It may fall on you and could cause injury.  
Place the machine on a stable and level surface.  
Request Regarding Maintenance  
Utilize our maintenance services.  
After purchasing the machine, contact your authorized TOSHIBA TEC representative for assistancii  
once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the  
machines and may cause a fire or a malfunction. Cleaning is particularly effective before humid rainy  
seasons.  
Our preventive maintenance service performs the periodic checks and other work required to maintain  
the quality and performance of the machines, preventing accidents beforehand.  
For details, please consult your authorized TOSHIBA TEC representative for assistance.  
Using insecticides and other chemicals  
Do not expose the machines to insecticides or other volatile solvents. This will cause the cabinet or  
other parts to deteriorate or cause the paint to peel.  
(ii)  
 
EO1-12031  
TABLE OF CONTENTS  
Page  
1. INTRODUCTION----------------------------------------------------------------------------------------1- 1  
1.1 Accessories--------------------------------------------------------------------------------------------------1- 1  
2. APPEARANCE------------------------------------------------------------------------------------------2- 1  
2.1 Standard Model---------------------------------------------------------------------------------------------2- 1  
2.2 Available Options-------------------------------------------------------------------------------------------2- 3  
2.3 Example of POS Terminal with Some Options -----------------------------------------------------2- 3  
3. CONNECTORS -----------------------------------------------------------------------------------------3- 1  
4. INSTALLATION PROCEDURE---------------------------------------------------------------------4- 1  
4.1 Environment for Installation------------------------------------------------------------------------------4- 1  
4.2 Connecting the AC Plug----------------------------------------------------------------------------------4- 2  
5. ADJUSTMENT ------------------------------------------------------------------------------------------5- 1  
5.1 Tilt Angle Adjustment--------------------------------------------------------------------------------------5- 1  
5.2 Brightness Adjustment------------------------------------------------------------------------------------5- 2  
5.3 Speaker Volume Adjustment----------------------------------------------------------------------------5- 2  
5.4 Beep Volume Adjustment -------------------------------------------------------------------------------5- 2  
6. MAGNETIC CARD READER (OPTION) ---------------------------------------------------------6- 1  
6.1 How to Read Magnetic Card ----------------------------------------------------------------------------6- 1  
7. iBUTTON® (OPTION)----------------------------------------------------------------------------------7- 1  
7.1 How to Read iButton --------------------------------------------------------------------------------------7- 1  
8. GENERAL MAINTENANCE -------------------------------------------------------------------------8- 1  
8.1 Cleaning ------------------------------------------------------------------------------------------------------8- 1  
9. TROUBLESHOOTING --------------------------------------------------------------------------------9- 1  
10. SPECIFICATIONS ----------------------------------------------------------------------------------- 10- 1  
10.1 Basic Specifications ------------------------------------------------------------------------------------- 10- 1  
10.2 Options------------------------------------------------------------------------------------------------------ 10- 3  
CAUTION!  
1. This manual may not be copied in whole or in part without prior written permission of  
TOSHIBA TEC.  
2. The contents of this manual may be changed without notification.  
3. Please refer to your local Authorised Service representative with regard to any queries you  
may have in this manual.  
 
1. INTRODUCTION  
EO1-12031  
1.1 Accessories  
1. INTRODUCTION  
Thank you for choosing the TOSHIBA POS Terminal. This POS terminal contains all the high  
performance register functions necessary for a specialty store POS terminal and enables the user  
oriented system configuration.  
The operation panel can be chosen from 12-inch TFT display and 15-inch TFT display.  
This manual describes the functions and handling of this POS terminal and should be read carefully to  
help gain maximum performance and life from your POS terminal. For most queries please refer to  
this manual and keep it safe for future reference.  
1.1 Accessories  
Confirm that all the following accessories are contained in the carton. If any accessories are missing  
or damaged, contact your TOSHIBA TEC service representative.  
Owner’s Manual (1 copy)  
Bind Screw M-3x3  
(8 pcs.)  
1- 1  
 
2. APPEARANCE  
EO1-12031  
2.1 Standard Model  
2. APPEARANCE  
2.1 Standard Model  
12-inch display POS terminal  
MIC IN  
Beep Volume  
12” TFT Color Display  
with Touch Panel  
Reset Switch  
Power Switch  
Speaker Volume  
HDD LED (Yellow)  
Power LED (Green)  
Speaker  
Brightness Control  
15-inch display POS terminal  
Beep Volume  
MIC IN  
15” TFT Color Display  
with Touch Panel  
Reset Switch  
Power Switch  
Speaker Volume  
Speaker  
HDD LED (Yellow)  
Power LED (Green)  
Brightness Control  
2- 1  
 
2. APPEARANCE  
EO1-12031  
2.1 Standard Model  
1) Power LED (Green)  
This is the LED to indicate the power ON/OFF status of the POS terminal. The green LED is illuminated  
when the power is ON.  
2) HDD LED (Yellow)  
The yellow LED is illuminated during the access to the hard disk drive.  
3) Power Switch  
This is the switch to turn the power of the POS terminal ON or OFF.  
4) Reset Switch  
This switch is used to reset the unit when the POS terminal hangs up.  
CAUTION!  
Do not press the Reset Switch unnecessarily. Doing so may cause an error.  
5) Speaker Volume  
This is used to adjust the internal speaker volume.  
6) MIC IN  
This connector is used to connect a monophonic microphone via the mono mini jack terminal.  
7) Beep Volume  
This is used to adjust the internal beep speaker volume.  
8) Brightness Control  
This is used to adjust the brightness of the operator’s display.  
2- 2  
 
2. APPEARANCE  
EO1-12031  
2.2 Available Options  
2.2 Available Options  
15" 2nd Display  
12" 2nd Display  
PCMCIA/CF Board  
LIU  
LVDS PC Board  
LIU Stand  
Pole Unit  
12" or 15" POS Terminal  
Relay PC Board  
iButton Unit  
MCR  
COM 5 or 6  
2.3 Examples of POS Terminal with Some Options  
Example of ST-71 with an optional  
MCR and 2nd display  
Example of ST-71 with an optional MCR,  
iButton, and 2nd display  
MCR Unit  
(Option)  
2nd display  
(Option)  
2nd Display  
(Option)  
MCR Unit  
(Option)  
MCR Unit (Option)  
(When attached to  
the left side of the  
display)  
iButton (Option)  
Example of ST-71 with an optional LIU  
(Front display: 12/15-inch TFT, Rear display: LIU + LIU stand)  
Example of ST-71 with an optional LIU  
(Front display: 12/15-inch TFT, Rear display: LIU + Pole unit + LIU stand)  
LIU (Option)  
LIU (Option)  
Pole Unit (Option)  
LIU Stand (Option)  
LIU Stand (Option)  
2- 3  
 
2. APPEARANCE  
EO1-12031  
2.3 Examples of POS Terminal with Some Options  
CAUTION!  
Do not strongly push or scratch the edge of the touch screen (the shaded part of the following figure)  
with a sharp tool, such as a nail and a pen. Doing this may damage the touch panel.  
4 mm  
4 mm  
2- 4  
 
3. CONNECTORS  
EO1-12031  
3. CONNECTORS  
3. CONNECTORS  
AC Inlet  
LVDS1  
LVDS2*  
PS/2 Mouse  
USB5  
COM6*  
COM5*  
P-USB3  
PCMCIA*  
CF Card*  
24V DC  
outlet  
COM1  
Display Power  
and Signal  
COM2  
COM3  
Line Out  
USB4  
LAN  
DRW2  
DRW1  
LPT  
PS/2 Keyboard  
COM4  
VGA  
*: Option  
Connector  
Description  
AC inlet  
A connector for the AC inlet  
24V DC outlet  
A terminal of a DC 24V line to which the power cable of the Receipt/Journal  
printer is connected.  
PS/2 (Mouse, Keyboard)  
Mini-DIN 6-pin female type connector  
Connector for the PS/2 type mouse, Connector for the PS/2 type keyboard  
Connector for the USB (Universal Serial Bus) interface USB V2.0/1.1 and UHCI  
(conforming to Universal Hub Controller Interface V2.0/1.1)  
NOTE: USB functions may not be supported depending on the Operating  
System.  
USB3 (USB supplied with  
power)  
USB4,5 (General 5V USB)  
USB3 is a USB socket supplied with power, which is 1 port of 24V USB. USB4  
and USB5 can be used as general 5V USB connectors.  
Modular type connector for the 10BASE-T/100BASE-TX LAN interface  
A 24V type drawer is connectable.  
Expandable LCD interface (LVDS2 is a option.)  
Expandable VGA interface  
LAN  
DRW1, DRW2  
LVDS1, 2  
VGA  
15-pin VGA female type connector  
COM1, 2  
D-sub 9-pin male type connector (without power)  
A slot scanner, modem, serial interface type scale, EFT, etc. are connectable.  
D-sub 9-pin female type connector (with +5V, +12V output)  
A line display unit or RS-232C type hand scanner is connectable.  
NOTES:  
COM3, 4, 5, 6  
1. COM4 cannot be used when the touch panel TFT is connected to the POS  
terminal.  
2. When an optional back indicator unit is installed on the POS terminal, COM3  
is not available.  
3. COM5 and COM6 are available only when the optional kit is installed.  
LPT1  
D-sub 25-pin female connector  
Printer, etc. having a Centronics interface or equivalent are connectable.  
Used for connecting an external speaker via the stereo mini jack terminal  
TYPE II compact flash card conforming to CFA (Compact Flash Association)  
standard can be used.  
Line-out  
CF Card interface slot  
PC Card interface slot  
This complies with PC Card Standard Release 8.0.  
32-bit Card Bus card and 16-bit PC card are supported. One slot is provided and  
accepts up to TYPE II card.  
3- 1  
 
4. INSTALLATION PROCEDURE  
EO1-12031  
4.1 Environment for Installation  
4. INSTALLATION PROCEDURE  
WARNING!  
1. Care must be taken not to get your fingers caught between the LCD Frame and the POS terminal  
when bending the display backward.  
2. DO NOT raise the LCD Frame while the Front Cover is not in position. When the LCD Frame is raised  
at right angle (90°) or more, the LCD may fall under its own weight, and your fingers may be caught.  
CAUTION!  
When removing the protective film from the display surface, please be sure to do it slowly. If it is done  
quickly, static electricity may generate, and the TFT may be damaged.  
4.1 Environment for Installation  
CAUTION!  
When installing the POS terminal, take the following precautions. Failure to do this may cause fire,  
electric shock, or injury.  
1. Avoid locations where it is subject to the following:  
Direct sunlight  
High temperature, high humidity  
Rapid change in temperature  
Excessive vibration  
Dust  
2. Keep away from any devices that emit magnetism or electromagnetic wave.  
3. Keep away from flame or moisture.  
4. Be sure to place the POS terminal on a level and stable surface.  
1. Place the POS terminal on a level surface.  
2. Provide a minimum space to the left, right, front and rear of the POS terminal for proper cooling. (The  
unit has air vents and a fan on the front and left. Spaces should be provided to prevent the air vents  
from being blocked and the air flow from being obstructed.)  
80 mm  
(See NOTE.)  
80 mm  
80 mm  
See NOTE.  
80 mm  
NOTE: A fan is provided on these sides. Do not prevent the ventilation of the fan.  
4- 1  
 
4. INSTALLATION PROCEDURE  
EO1-12031  
4.2 Connecting the AC Plug  
4.2 Connecting the AC Plug  
NOTE: Since the power cord set is not supplied with this unit, please purchase an approved one that meets the  
following standard from your authorized TOSHIBA TEC representative.  
1. Gently bend the Display backward by the both sides of the LCD Frame.  
LCD Frame  
2. Remove the two screws that secure the Front Cover. Press the center of the Front Cover’s top to  
release the hook, and pull out the Front Cover.  
PUSH  
Hook  
Screw  
Front Cover  
Screw  
4- 2  
 
4. INSTALLATION PROCEDURE  
EO1-12031  
4.2 Connecting the AC Plug  
3. Fully insert the Power Cord Plug into the Inlet of the POS terminal.  
Inlet  
Power Cord Plug  
4. Fit the Front Cover into the front of the POS terminal, and secure it with the two screws.  
Screw  
Front Cover  
Screw  
4- 3  
 
5. ADJUSTMENT  
EO1-12031  
5.1 Tilt Angle Adjustment  
5. ADJUSTMENT  
Tilt angle and brightness of the operator’s display can be adjusted.  
Adjustment method is common to both of 12-inch display model and 15-inch display model.  
CAUTION!  
1. Do not adjust the display angle by holding the LCD panel. Doing so may damage the unit. Be  
sure to hold the LCD frame.  
2. Care must be taken not to catch your fingers between POS terminal and the LCD Frame when  
bending the display backward.  
5.1 Tilt Angle Adjustment  
The tilt angle of the operator’s display can be adjusted freely in a range of 0° to 90°.  
Hold both sides of the LCD frame, and slowly push the display backward to your best angle.  
<Single display type (Standard)>  
0° to 90°  
LCD Frame  
<Dual display type (Option)>  
0° to 90°  
0° to 90°  
5- 1  
 
5. ADJUSTMENT  
EO1-12031  
5.2 Brightness Adjustment  
The angle of the optional LIU is also adjustable as follows.  
0° to 45°  
0° to 145°  
(in both directions)  
<Tilt range>  
<Swivel range>  
5.2 Brightness Adjustment  
The brightness control is provided on the lower right of the operator’s display.  
Turning it to the left makes the display darker, and turning it to the right makes the display brighter.  
Darke  
r
Brightness Control  
Brighter  
5.3 Speaker Volume Adjustment  
When it is turned counterclockwise, the sound volume turns up.  
When it is turned clockwise, the sound volume turns down.  
5.4 Beep Volume Adjsutment  
When it is turned counterclockwise, the sound volume turns up.  
When it is turned clockwise, the sound volume turns down.  
Beep Volume  
Speaker Volume  
5- 2  
 
6. MAGNETIC CARD READER (OPTION)  
EO1-12031  
6.1 How to Read Magnetic Card  
6. MAGNETIC CARD READER (OPTION)  
The optional magnetic card reader can be installed on either side of the POS terminal.  
6.1 How to Read Magnetic Card  
Insert the magnetic card into the upper portion of the magnetic card reader slot and slowly move the card  
downward.  
Magnetic Card  
MCR Unit (Option)  
NOTE: Moving the magnetic card too fast or too slowly may cause a read error.  
6- 1  
 
7. iBUTTON® (OPTION)  
EO1-12031  
7.1 How to Read iButton  
7. iBUTTON® (OPTION)  
The optional iButton unit can be installed on the bottom of the LCD.  
7.1 How to Read iButton  
CAUTION!  
1. Keep storage media, like a floppy disk, away from the touch probe. The stored data may be  
destroyed by the magnet of the touch probe.  
2. Keep a metal object like a paper clip away from the touch probe. If such an object is attached to the  
touch probe, it may cause a short-circuit.  
Data stored in an iButton can be read by attaching the iButton key to the touch probe. The iButton key is  
held by the magnet of the touch probe.  
iButton Unit  
(Option)  
iButton Key  
Touch Probe  
7- 1  
 
8. GENERAL MAINTENANCE  
EO1-12031  
8.1 Cleaning  
8. GENERAL MAINTENANCE  
8.1 Cleaning  
WARNING!  
1. Be sure to disconnect the power cord prior to performing any maintenance.  
2. Do not pour water directly on or wipe the operator’s display with a soaked cloth, as this may cause  
fire, electric shock, or machine failure.  
CAUTION!  
1. Never use an organic solvent like thinners or benzene for cleaning. Using such solvents may  
discolor the covers.  
2. Do not use any sharp object to clean the operator’s display. Doing so may cause an operator’s  
display failure.  
3. Do not insert the nozzle of an air blower into the magnetic card reader slot. Doing so may  
damage the scanning head, resulting in the magnetic card reader failure.  
To help retain the high quality and performance of your POS Terminal, it should be cleaned regularly. The  
greater the usage on the POS Terminal, the more frequent the cleaning. (i.e. low usage = weekly: high  
usage = daily)  
• Cleaning the Operator’s Display  
Clean the surface of the operator’s display with a soft dry cloth or with an electrostatic free cleaner for  
automated office equipment.  
• Cleaning the Covers  
Wipe the covers with a soft dry cloth or soft cloth slightly moistened with mild detergent. After using  
detergent for cleaning, be sure to wipe it off with a slightly moistened cloth.  
8- 1  
 
9. TROUBLESHOOTING  
EO1-12031  
9. TROUBLESHOOTING  
9. TROUBLESHOOTING  
WARNING!  
If you cannot solve a problem with the following solutions, do not attempt to repair it by yourself. Turn  
the power off, unplug the POS Terminal, then contact the nearest TOSHIBA TEC service  
representative for assistance.  
Symptom  
Check point  
Solution  
The power does not Is the power cord plugged in correctly?  
Plug in correctly.  
turn on.  
Is the power supplied to the AC outlet?  
If it is not a power failure,  
check for the power supply to  
the AC outlet with another  
electric appliance.  
When the power is not  
supplied, contact your  
nearest power company.  
Check the circuit breaker.  
Refer to Section 5  
Adjustment and adjust the  
display angle.  
Refer to Section 5  
Adjustment and adjust the  
brightness properly.  
Has the circuit breaker blown?  
Does the operator’s display reflect  
sunlight or room light?  
Is the tilt angle adjusted properly?  
Is the brightness adjusted properly?  
The operator’s  
display is hard to see.  
Magnetic card reader Does the used card comply with the  
Use Track 1, 2 complying  
with ISO.  
does comply-not  
read the data.  
standard?  
Was the card moved too fast or too  
slowly?  
Move the card at the proper  
speed. (10~150 cm/sec.)  
Insert the card so that the  
magnetic strip faces the  
scanning head.  
Is the card reading direction correct?  
9- 1  
 
10. SPECIFICATIONS  
EO1-12031  
10.1 Basic Specifications  
10. SPECIFICATIONS  
10.1 Basic Specifications  
Item  
Description  
Input voltage  
AC 100V-240V +10%, -10% 50/60Hz 5.0A (115V)-2.5A (230V)  
DC24V +5%, -5%  
DC output voltage  
Operating temperature  
Relative humidity  
5°C to 35°C  
10% to 80%RH (no condensation)  
Dimensions  
15-inch LCD 359.9 mm (W) x 388.1 mm (D) x 371.4 mm (H)  
12-inch LCD 295.0 mm (W) x 386.8 mm (D) x 323.5 mm (H)  
15-inch LCD 12.5 Kg  
Weight  
12-inch LCD 11.5 Kg  
Power cord  
A power cord is not included in this product. Please use one complied with  
each country’s safety standard. For details, please contact the nearest  
TOSHIBA TEC service representative.  
CPU  
Intel Celeron® 2.0 GHz with 128 KB secondary cache  
BIOS ROM  
RAM  
1MB Flash ROM  
Capacity  
Type  
Standard 256MB (Max. 2GB)  
Max. 1GB/slot can be equipped.  
DDR SDRAM PC2100/2700, 2.5V unbuffered type, ECC/non ECC 184-pin  
DDR SDRAM DIMM connector, 2 slots installed  
Interface  
RS-232C x 6 (Standard: 4 + Option: 2), Parallel x 1, P-USB x 1, USB x 2,  
Drawer x 2 (24V type), PS/2 x 2, 24VDC OUT (DIN 3-pin) x 1  
Display interface  
LCD Interface  
Touch panel method  
Hard Disk Drive (HDD)  
LAN interface  
PC card  
VGA x 1 channel (on-board, standard)  
Standard LVDS1 x 1, LVDS1 + LVDS2 (Option)  
Analog resistor film  
Max. 2 units of 2.5-inch HDD (option) can be connected.  
10 BASE-T, 100 BASE-TX (Wake on LAN support)  
PCMCIA TYPE II x 1 (option)  
CF card  
CF card TYPE II x 1 (option)  
MCR  
ISO-1,2-track one-sided type (option)  
Sound generator  
AC97 interface; LINE OUT x 1, MIC IN x 1, Built-in speaker (Monaural  
sound)  
Support OS  
Windows 2000, Windows XP, Certified Linux  
10- 1  
 
10. SPECIFICATIONS  
EO1-12031  
10.1 Basic Specifications  
Item  
Description  
12-inch display  
15-inch display  
Operator’s Display type  
Display  
12.1-inch color TFT with touch  
panel  
15.0-inch color TFT with touch  
panel  
Display size  
12.1-inch 800 x 600 dots  
262K color (262,144 colors)  
320 cd/m2 320 nit  
15.0-inch 1024 x 768 dots  
262K color (262,144 colors)  
280 cd/m2 280 nit  
Number of colors  
Brightness  
Display area  
Dot size  
246 mm (W) x 184.5 mm (H)  
0.3075 mm (W) x 0.3075 mm (H)  
304.1 mm (W) x 228.1 mm (H)  
0.297 mm (W) x 0.297 mm (H)  
Touch panel  
Analog Resistor Film  
(1024 x 1024 dots)  
Analog Resistor Film  
(1024 x 1024 dots)  
Adjustment  
mechanism  
Brightness volume (TFT) and Tilt angle (Free adjustment in a range of  
0° to 90°)  
No swivel adjustment  
LIU  
Number of displayed 5 x 7 dot fluorescent display 20 digits x 2 lines  
(Option)  
characters  
20 triangles under the 2nd line  
Display color  
Blue  
Display  
area/character size  
Character size: 5.5 mm (W) x 10.5 mm (H)  
Character pitch: 7.4 mm (W) x 15.5 mm (H)  
Type font  
182 types of half width ANK  
Display angle  
Tilt: 0° to 45° (9 step, 5deg, each)  
Swivel: 0° to 145° (in both directions)  
Interface with  
ENGINE  
RS-232C interface (with power)  
10- 2  
 
10. SPECIFICATIONS  
EO1-12031  
10.2 Options  
10.2 Options  
Option name  
Model  
Description  
24V-drive standard drawer  
(with screw holes on the left and the rear for installing the  
POLST-51)  
Dimensions and Weight:  
DRWST-51A-4MVK-QM-R  
DRWST-51A-8MVK-QM-R  
460(W) x 400(D) x 115(H) mm, 10 Kg  
Money Case Type: MC4,8  
Drawer unit  
Type  
Bill holder Coin tray Mini coin case CDC  
Remarks  
Drawer type  
4MVK-QM  
8MVK-QM  
5
4
5
6
No  
1
Yes With media slot  
Yes With media slot  
12.1-inch TFT color display to be installed onto the POS  
terminal  
TFTST-71-2A-QM-R  
TFTST-71-5A-QM-R  
KIT-71-DSP1-QM-R  
LIUST-71-BAAK-QM-R  
2nd display unit  
LVDS board  
15.1-inch TFT color display to be installed onto the POS  
terminal  
Used to connect a TFTST-71 optional 2nd display unit.  
Line indicator unit  
(LIU)  
20 characters x 2 lines dot display to be installed onto the  
POS terminal  
Pole and extension cable for attaching an LIUST-71 optional  
line indicator unit at the level of 235 mm from the standard  
position  
Pole unit  
KIT-71-POLE-QM-R  
A stand for installing an LIUST-71 optional line indicator unit  
onto the POS terminal  
LIU stand  
KIT-71-BASE-QM-R  
TRST-56-P-1K-QM-R  
TRST-56-S-1K-QM-R  
Parallel interface single thermal printer for 80 mm wide paper  
Cabinet color: Cool Black  
Printer unit  
Serial interface single thermal printer for 80 mm wide paper  
Cabinet color: Cool Black  
PC card/CF card interface kit  
This kit conforms to the 32-bit CardBus (Card-32) card and  
the 16-bit PC card (Card-16).  
A slot is provided on the board, which supports up to  
PCMCIA Type II or CF card TYPE II.  
PCMCIA/CF  
interface board  
MIFST-71-2-QM  
COM5 and COM6  
connectors  
KIT-71-COM-QM-R  
MCRST-71-3-QM-R  
KIT-71-BTN1-QM-R  
KIT-71-RELY-QM-R  
COM5 or COM6 connector and cable kit  
Magnetic card  
reader (MCR)  
ISO Track 1 and 2 type magnetic card reader kit  
iButton unit to be installed onto the POS terminal  
(An iButton key is not included.)  
iButton  
Relay PC board  
Used to control an optional MCR unit or iButton unit.  
NOTE:  
Model names that end with "-R" are RoHS compliant models. If "-R" is not attached, that model is non RoHS  
compliant.  
Never install non RoHS compliant optional equipment or parts on a RoHS compliant machine which is supposed  
to be used in the countries that enforce the RoHS directive, as doing this is legally prohibited.  
10- 3  
 
English  
Waste Recycling information for users:  
Following information is only for EU-member states:  
The crossed out wheeled bin symbol is used to indicate that the product must not be treated as general household waste.  
By ensuring that this product is disposed of correctly you will be helping to prevent potentially negative consequences for  
the environment and human health, which could otherwise be caused by incorrect waste handling of this product.  
For more detailed information about the take-back and recycling of this equipment, please contact the supplier that  
provided you with the product in question.  
French  
Information aux utilisateurs concernant le recyclage des déchets:  
Les informations suivantes sont uniquement destinées aux pays membres de l’Union Européenne:  
L’utilisation du symbole de "poubelle à roulettes barrée" indique que ce produit ne doit pas être traité comme un déchet  
ménager classique.  
En vous assurant que ce produit est correctement mis au rebut, vous participerez à la prévention de l’environnement et  
de la santé publique, contre des conséquences négatives potentielles qui pourraient résulter d’un traitement inapproprié  
des déchets de ce produit. Pour obtenir des informations complémentaires concernant la récupération et le recyclage de  
ce produit, veuillez contacter le fournisseur auprès duquel vous avez acheté le produit.  
German  
Wiederverwertungsinformationen für Verbraucher:  
Die folgenden Informationen gelten nur für EU-Mitgliedsstaaten:  
Das durchgestrichene Mülltonnensymbol weist darauf hin, dass dieses Produkt nicht wie allgemeiner Haushaltsmüll  
behandelt werden darf.  
Indem Sie aktiv mitwirken, dieses Produkt ordnungsgemäß zu entsorgen, helfen Sie mit, mögliche negative  
Auswirkungen auf die Umwelt sowie die menschliche Gesundheit zu vermeiden, die sonst durch die unsachgemäße  
Entsorgung dieses Produktes beeinträchtigt werden könnten.  
Für nährere Informationen zur Rücknahme und Wiederverwertung dieses Produktes wenden sie sich bitte an den  
Lieferanten, von dem Sie dieses Produkt erworben haben.  
Spanish  
Información para usuarios sobre el reciclaje de residuos:  
La siguiente información sólo concierne a los Estados Miembros de la UE:  
El uso del símbolo de un contenedor con ruedas tachado indica que este producto no puede ser tratado como si fuera  
un residuo doméstico.  
Asegurando que nos deshacemos de este producto de forma correcta, ayudaremos a evitar potenciales consecuencias  
negativas tanto para el medio ambiente como para la salud pública, que podrían producirse debido a un tratamiento  
inapropiado de este producto. Para obtener una información más detallada sobre la recogida y reciclaje de su producto,  
por favor, póngase en contacto con el proveedor donde lo compró.  
Dutch  
Gebruikersinformatie over het recycleren van afval:  
De volgende informatie geldt enkel in EU-lidstaten:  
Het symbool met de doorkruiste afvalbak geeft aan dat dit product niet mag worden behandeld als algemeen  
huishoudelijk af val.  
Door dit product op de juiste manier van de hand te doen beschermt u het milieu en de volksgezondheid tegen mogelijke  
negatieve gevolgen, die anders zouden kunnen voortvloeien uit het onjuist verwerken van de resten van dit product.  
Voor gedetailleerde informatie over het terugnemen en recycleren van dit product, gelieve contact op te nemen met de  
leverancier van dit product.  
Italian  
Informazioni sul riciclo del prodotto:  
Le seguenti informazioni riguardano gli stati membri EU:  
Il simbolo con il bidone sbarrato indica il non poter smaltire questo prodotto come rifiuto domestico.  
L'accertamento che questo prodotto sia smaltito correttamente contribuirà ad impedire le potenziali conseguenze  
negative per l'ambiente e la salute umana che potrebbero essere causati, al contrario, dall'errato smaltimento dello  
stesso. Per informazioni più dettagliate sulle modalita di resa e riciclaggio di questo prodotto mettetevi in contatto con il  
fornitore da cui l'avete aquistato.  
Portuguese  
Informação sobre reciclagem:  
A informação que se segue é apenas dirigida a países membros da CEE:  
A utilização deste símbolo indica que este produto não pode ser tratado como lixo comum.  
Ao assegurar-se que este produto é tratado correctamente está a ajudar a prevenir potenciais consequências negativas  
para o ambiente e para a saúde humana, que poderiam ser causadas pelo inapropriado tratamento deste produto.  
Para mais informação sobre a reciclagem e tratamento deste produto, contacte o seu fornecedor.  
 
 
PRINTED IN TAIWAN  
EO1-12031  
E
 

Tascam CD Player CD X1700 User Manual
TDK Computer Drive SDG8B Series User Manual
Tokina Camera Accessories TVR2714 User Manual
Toshiba Network Card AD368 User Manual
Trane Universal Remote CNT PRC002 EN User Manual
Triarch Indoor Furnishings 33165 User Manual
Tripp Lite Power Supply AG 0018 User Manual
Tripp Lite TV Cables N546 20M User Manual
ViewSonic Computer Monitor E90F User Manual
Vizio Network Card TL WN721N User Manual